A will-fit part, by its own definition, will fit. But the key point is, will it work?
It seems to make a lot of sense to take a long, hard look at using non-OEM replacement
parts on lift trucks. After all, when breakdowns occur, everyone wants to get the unit up
and running as fast and as inexpensively as possible. But the fallacy of a will-fit,
non-OEM part is that there is no guarantee that it meets the engineering specifications
set by the manufacturer.
A will-fit part, by its own definition, will fit. But the key point is, will it work? A
will-fit part almost always looks the same, installs the same, and at first blush, may
even work the same. "However, that's not always the case," says Bryan
Uittenbogaard, senior engineer at CLARK Material Handling Company. "It's the internal
workings that make the difference. Take filters as an example. Anyone can put together a
filter that looks just like a Clark filter."
There's no way to tell the difference, even if you hold them side by side. The box will
say that it contains the same amount of filtering media, and that it meets minimum
standards, but the key is the type of filtering media that is used. The paper is the
difference. With a Clark filter, you know it meets the specifications set out by Clark,
while the other may only meet the very minimum specifications.
For example, Clark and its filter manufacturer recently completed testing a hydraulic
filter for Clark Genesis Series lift trucks. The testing represents weeks of laboratory
testing and two years of test track work. It measured the filter's dirt-holding ability,
clean filter pressure drop, filter integrity, hydraulic fluid compatibility, burst
pressure, element flow fatigue, element end-loading capacity and end cap construction.
These tests resulted in an exclusive state-of-the-art hydraulic filter that assures
contaminants will be effectively controlled. That means greater equipment reliability and
overall lower operating costs from less unscheduled downtime. "There are no
assurances like that with will-fit filters," Uittenbogaard points out.
Put the brakes on will-fit failures
As shown in the photo at right, you can run into real trouble when you use will-fit parts.
"The brake shoes shown here were actually on a lift truck, then taken off and run on
a test stand to simulate normal use. These will-fit shoes looked exactly like Clark brake
shoes, but the bonding that holds the pad to the shoe let loose, which would result in
loss of braking power," says Uittenbogaard.
Although the pads show little wear, the failure took the lift truck out of service. The
cost of the downtime far exceeded the minimal difference in the cost of the Clark brand
brake shoes. While the brake shoes offer a dramatic look at what can happen with low-cost
will-fit products, other will-fit components can cause more elusive problems. Electric
lift trucks, with their high-tech components, are especially vulnerable to sporadic
problems that in the end are often traced to will-fit replacement parts.
OEM logic boards maintain control
"Will-fit control or logic cards are classic examples," says Arun Seksaria,
electronics engineering specialist for Clark electric lift trucks. "We have often
seen erratic operation with will-fit cards," he says.
"If there is a voltage spike or heating in the card, the operator will see erratic
operation or failure. Consider the damage an erratically operating lift truck can do, and
the slight price difference doesn't make sense. Using will-fit parts is a risk management
issue." Seksaria says will-fit controller or logic cards are not duplicates of OEM
boards. Instead, they mimic the actions required, using similar hardware and software that
may not operate correctly under certain conditions.
"The software and hardware look similar, but are different. It is like a
reflection in the mirror; it's not a true picture of the real thing." Often, users
attempt to diagnose electric lift truck problems, replacing a will-fit board with another
will-fit board and the same problem surfaces. Therefore, they surmise it's some other
component. They replace other parts although they are not faulty, increasing repair costs.
"In the end, when a service person is finally called in, the logic board is
replaced with an OEM board and the problem disappears. Even though the will-fit logic
board looks and fits like the OEM board, the tolerances under which it is produced are
much wider than the OEM board," Seksaria says. That difference in tolerance is very
important in electronic applications. "It's these tight tolerances that save the
bacon," he adds.
Problems spread like a virus
Another common electric lift truck problem results from using non-OEM battery connectors
to charge batteries. These connectors look very similar to the original equipment, but the
contact tips and retaining springs are less resilient. After extended use, they fail, says
Glen Wood, Clark product service manager for electric lift trucks.
"When these springs and contacts begin to fail, they cause arcing that damages
contact tips. This causes incomplete charging and heat buildup, which greatly affects
battery life. And once one contact tip on a battery, truck or charger is damaged, it will
damage any other contact that is connected to it," Wood says. "We often see
cases where will-fit connectors have been used, and over time, the entire fleet needs new
connectors. That's why using OEM connectors is so important. It can save you money in the
long run, especially in fleet operations."
It's all in the connection
Wood offers one other tip that can save lift truck operators headaches. When adding
electrically powered accessories to Clark lift trucks, use Deutsche-type connectors as
opposed to other connector types. Clark uses the Deutsche-type connectors because they
easily withstand the rigors of industrial lift truck operation; others can not. "You
can get a kit from your Clark dealer that carries tooling and an assortment of pieces to
put together the proper connections needed for accessories.
"It's a simple way to assure you have the parts you need. It will likely save you
money in the long run with less downtime and unexpected maintenance costs due to failed
accessories," he says.
Compelling reasons for Clark components
These are just a few examples of how will-fit parts can affect lift truck operation.
Often, the price difference between a Clark brand part and a will-fit component is
negligible,and when you add in unscheduled or unplanned downtime due to premature failure,
the cost structure quickly favors Clark brand parts.
